2-4-1 ORIGAMI HANG GLIDER PATTERN PDF

年7月16日 There is now a simpler paper glider that is easier to make Part 2 of 3 Links to all parts at Pattern here. Origami Tumblewing and Hang Glider Origami Instructions for Origami Tumblewing: html. Now the rectangle of paper is free, and sticking up in this diagram. previous folds. drawing (if the paper is stiff enough) or hang it on stage 3: rearranging. 2- 6 on the other 3 corners 10 9 3 2 4 1 Continue to colapse the box, Finished box. If you held it level or with the nose slightly downwards it will glide gently down .

Author: Zololl Daira
Country: Germany
Language: English (Spanish)
Genre: Education
Published (Last): 1 September 2009
Pages: 90
PDF File Size: 11.47 Mb
ePub File Size: 13.83 Mb
ISBN: 791-1-98640-849-9
Downloads: 94156
Price: Free* [*Free Regsitration Required]
Uploader: Mek

The model also required two 2×1 rectangles. Grab the outer Then if you fold it up as you pull out the last tail, well all but a tiny thing, we do at the layers it should give you lots of material end of the process.

The premise behind this series of chess pieces was to design a chess set that a could be folded from the same sized squares, b were 3D, and c were easily distinguishable. A layer swings out from behind at the 4 tiny 9. This causes the wing to take on a curve. For your first attempt, begin with a 3×7 rectangle considerably larger than a dollar bill.

  AZERRAD MICHAEL.COME AS YOU ARE THE STORY OF NIRVANA PDF

Separate and draw the diagonal edge of the first Fold as shown, crease firmly, and layer of the flaps on each side towards the centre, unfold. Roll the leg down as far as it will go. Swing the large flaps back. Valley through intersection of creases. Shape the bottom of the body and the dorsal fin with gentle mountain folds.

Here is where a hard flat surface comes in patern. You can use any integer ratio of 4×1 or longer. Turn the model over side-to-side. If you stopped when it started to get strange then you should have something sort of like this.

Pull the flap through. Repeat the left; repeat behind. Then spread the pinch mark of step Practice this in a separate sheet first.

Origami Hang Glider

Unfold and tuck in two triangles pocket. Fold the wings down. Repeat on left, and are concave. Precrease outer quarters into eighths all valley folds.

All Rights Reserved D C align The 2-4-11 should look Swing one flap up a portion image. Round off with Begin black side up.

Valley fold the thick point at the left Valley fold the hant point at the left down to the intersection of the edge Valley fold the entire model in half, down to the bottom point and and the angle bisector from Step 8 right side over left. In order to do this effectively and without ripping the paper, you will ptatern to push in like an open sink the bit of the hump on the back that is hidden inside the neck Outside reverse fold the flap again, bisecting indicated by the x-ray line.

  IVO ANDRIC NA DRINI CUPRIJA CELA KNJIGA PDF

Creases exist as shown. Precrease sides of flap and With a soft crease, curve the tail fin. The leaf with crawling caterpillar completed!

Bronco Technology & Engineering: Eng Design

Repeat on the next flap. Us finicky types would look at this and say, oh! Only the tiny valley fold is a new crease. Precrease into eighth squares all valley folds. Rabbit ear the front pattsrn.

Note pttern the Narrow the neck by mountain folding some of crease lines for the crimp do not meet on the the flap in front inside; as you do this, lattern small top of the neck — you’ll have to spread some bit of the bottom of the head will be squashed paper and push out a bit from the inside to do into a gusset inside.

Flip the wing, head, and tail over. Wrap a single layer Fold the flap to the tip. Petal fold the preliminary base.